I learnt a great deal from my first two building projects and much to my own surprise was ready and feeling confident at having a go at a complete scratch build back in May 2017 when this post first appeared.

—000—

28mm Building Project No: 3 – Livery Stable

Having completed two building projects I was ready to have a go at scratch building one.  I already knew that I wanted to build a Livery Stable and had in mind a rough idea of how it would look when completed.  To be fair the idea was based upon an old Britain’s Livery Stable (see image below) which I used to play with as a kid.

My first step was to put my design down on paper.  Having taken account of the base size, and working to a scale of 28mm equals 6 feet (and therefore 5mm equals approximately 1 foot), I drew the outline on graph paper (front, back and sides). Coffee stirrers were then cut to shape and using pva glue were stuck to card.  I used thick card, the type they use for making picture frame mounts.

Outline graph paper drawings and coffee stirrers

As part of my design I intended to have a roof which could be removed in order to look inside, so coffee stirrers needed to be stuck to both sides of the cardboad. The one thing I had not accounted for was the contraction brought about by the pva drying.  As a consequence the dried walls curled up a little rather than lay flat. Had I weighted the sides down while drying things might have been better.  The problem wasn’t insurmountable but it became clear that I needed to redesign the inside slightly so that the sides could be braced and pulled together when assembled and glued.

Early internal images showing the upper flooring and stable posts which were used to brace the sides at assembly

You will notice from the images above that the inside was also painted at this stage as it was much easier to man handle the model and gain access to all internal areas. My next steps were to add the door frames, construct the winch system, build the doors and begin the roof.  Coffee stirrers were again used and cut to size.

Various images of the outside and roof as the model began to come together and the figures started to be included

The right hand side of the roof as viewed in the above image was made to be removable while the left hand side was fixed.

The next stage was to paint the outside of the building but before doing so the wooden stirrers were roughed up using a wire brush and a modelling knife to add character which would become more obvious when the painting and dry brushing was done.  For painting I used a variety of different colour washes.  The washes were all created using various oil paints thinned out using white spirit.  I’m sure the purists would be horrified at the use of white spirit but I think the medium is great and use it all the time to thin and matt down oil paints.  The great thing about using real wooden coffee stirrers is the paint washes soak into the wood and in my opinion produce a nice finish.

With the building essentially complete attention was now directed to the figures and internal detailing.  The figures were mostly from http://www.dixon-minis.com – their Old West and American Civil War series.  Minor conversions were made to an artillery figure which was adjusted to pull the rope and the riden horse had saddle bags and a blanket added.

Ground work was essentially grit swept from the curb side and the greenery comprises of static grass, taller grass made from string and Seafoam Trees purchased from http://www.gaugemaster.com.  These trees are aimed at railway modellers but they are ideal for 28mm scale either as trees, bushes or climbing plants.  They are best painted with a diluted paint and then dressed with leaf materials applied using hair spray.

Images of the completed model appear below.

It was only after I had completed this model that I saw some images of roofs made of wooden shingles and thought they looked much better.  I decided that shingle roofs would be the next step towards improving my scratch built buildings.  More on this when I get round to publishing Building Project No: 4.

Welcome to TIM’s Memory Monday.

This post first appeard on the 21st May 2017 and it represents my second ever building project.

The original post has now been added to my archive site TIM Gone By.

TIM

—000—

28mm Building Project No: 2 – Pioneers Cabin

For this diorama I wanted to try to improve upon my first building project.  As a theme I decided to go with a pioneers cabin set in the middle of nowhere and where the early settlers would have had a non violent relationship with the local tribal indians.  The completed result appears below.

The building itself is another kit from Sarrisa (North American series) which has had some modifications.  As mentioned in my earlier Building Project No: 1 post, I wanted to add some depth to my next building and decided to use coffee stirrer’s to help achieve this.  I wasn’t bold enough to clad the building walls but did alter the roof.  Overall I was pleased with the outcome and with hindsight wished I had done something with the walls after all!

The building also featured a stone chimney.  Being laser etched the chimney looked very flat and so along with doing alterations to the roof I decided to build a new chimney using cat litter and filler.  Picture below.

Another first in this dioram was the introduction of “water”.  Woodland Scenics “Realistic Water” was used in the water trough and for creating the small waterfall and stream.  See below.

As with most things done for the first time there is a learning curve.  “Realistic Water” is like real water in that it runs everywhere and will escape all over the base unless it is properly contained.  If you want to add water to anything you do this stuff is great and there are some excellent tutorials on Youtube which can tell you how to use this stuff far better than I can.

The figures and wagon are all 28mm Dixon Miniatures.

A few more photo’s of this diorama are below.

For my next building project I decided I would try my hand at constructing a building completely from scratch.  More on that to follow.  In the meaanwhile I need to work on my photography skills as these images aren’t that great!

TIM

 

 

 

 

 

Welcome to TIM’s Memory Monday.

This week you get two back posts for the price of one.  The first post, Buildings – Introduction was first published back in March 2017 but as it didn’t have much to say (I was still finding my way around WordPress) I decided to add the post which followed it too – 28mm Building Project No: 1 – Undertakers & General Store.

Both are now on my archive site TIM Gone By.

TIM

—000—

Buildings – Introduction

As a kid I can remember Britains toys adding to their swoppet range by introducing western buildings and I can recall having been given the Bank, Jail, Hotel, Ranch House and Livery Stable as christmas and birthday presents.  I mention this only because it was these memories which inspired me to want to go beyond just painting figures to adding buildings to my modelling.

One of the first things to consider is the scale you want to build in.  As a modeller I had for the most part painted 54mm figures up to this point and as a consequence my initial idea was to build in this scale.  I soon realised that this presented two problems. Firstly, the constructed building would be quite large.  Secondly, how would I store or display it and keep it free of dust?

Pathetic as this sounds it took me a while to reach the obvious answer – build in a smaller scale!  I had only ever really considered 28mm to be a war gaming scale and as such had never properly looked at available figures and accessories. Needless to say a quick internet search opened up an entire new world and I haven’t looked back since.

I am by no means an expert on constructing buildings, if I were then I would would not be The Imperfect Modeller.  However, in a short period of time I have managed to move on from simply constructing and painting bought buildings to constructing my own frrom scratch, a most rewarding experience.

In this series of posts I will go through the evolution of my buildings.  In the meanwhile a picture below of a Livery Stable I constructed completely from scratch. It’s not without it’s faults (which I will highlight going forward) but it was only my third building ever.

—000—

28mm Building Project No: 1 – Undertakers & General Store

As mentioned in my previous post, I decided that scaling down to 28mm was my best option if I wanted to include buildings within my dioramas.  Having reached that decision a quick internet search for 28mm old west Buildings led to my discovery of Sarissa Precission’s website (http://www.sarissa-precision.com).  Sarissa have a whole host of buildings covering various periods including the Old West and North America both of which were of interest to me.

Sarissa’s buildings are made of MDF with laser etched detail, fit together perfectly and look very good when made up.  They were just what I was looking for and so I purchased two of them for the model pictured below.  The building on the left is Old West model code SmallPLUS Building 1 and the building on the right is Old West model code SmallPLUS Building 4.  For both buildings I also purchased the optional apex roof (I’m no fan of the characterless flat roof that comes as standard).

The aim of the diorama was to simply capture a moment in time on the street of a western town.  The buildings themselves were simply painted but, as can be seen from the additional photo’s below, I also chose to fit out the insides of both buildings. For reference all the figures in this diorama are from Dixon’s Miniatures (http://www.dixon-minis.com) and the various internal accessories are mostly from Frontline Wargaming (http://www.frontlinewargaming.co.uk).

Inside the General Store

Inside the Undertakers

The only minor adjustments I made to both buildings was to add clear plastic glazing where appropriate to doors and windows, to make a hole in each roof for the chimney of the wood burning stoves and to add the main signage (this was done using Word together with a downloaded western font which was printed and given a light colour wash).  Overall I was pleased with the outcome of my first building but as is often the case we are often our own worst critic and so, on closer inspection I felt there were improvements which could be made next time around.

A better painter than me would have been able to add depth to the wood of the building and to the roof tiles.  That was beyond my skill set and so my overall impression was that the end result was rather flat and lacking in character and depth.  How I could improve upon this came to me in Burger King while I was stirring my coffee – use real wooden coffee stirrers for cladding!  Which leads nicely onto the subject of my next post, My Second Building.

Welcome to TIM’s Memory Monday.

This is the beginning of a new weekly series of posts which will appear, oddly enough, each Monday!  As this is the first I will explain what is going and why.

Below you will find unedited the very first post I published on this blog.  It first went out on the 22nd March 2017.  Not surprisingly it was viewed by almost nobody but since then my blog has grown.  However, in my experience new readers and followers tend to read current content and move forward rather than look back.  With this in mind I thought it might be a good idea to repost my older content, excluding my Musings, to a wider audience.

In addition to the above, it is only a matter of time before I will be facing a WordPress memory problem.  I could of course simply upgrade my package but to be honest my blog isn’t a business portal so what’s the point?  Instead I have set up another site which I have called “TIM Gone By”.  It is an archive site and the post you see below has also been copied in its entirety to that site.

As we all know it is photographs and images which eat up our blog memory.  The same content of course enhances our blogs too.  The need therefore is to delete this media content and free up space.  With this in mind I will in six months time (I have put a note in my diary!) delete the photographs and images associated with the original post and this repost leaving only the written content.  Anyone wishing to see the complete post will be able to do so on “TIM Gone By”.  Thereafter it will be a rolling programme every week.

The big question of course is will this work and will it have an impact on this site in anyway?  Fucked if I know, let’s find out!

TIM

—000—

This post was first published by TIM on the 22nd March 2017.  Enjoy.

*****

Welcome to TIM – The Imperfect Modeller.

Most of my modelling is geared to the Old West but occasionally a figure comes along which catches my eye and I’m happy to give that a go.

In terms of scale I paint 28mm to 54mm figures although my dioramas tend to be exclusively 28mm due to size constraints.

As this is my first blog and my first post I thought it best to start with some images of my work. In future posts I will describe some of these and other models in greater detail and refer to techniques used  and also list materials and suppliers.

Please feel free to comment and ask any questions.

Thank you for looking.

*******

Left – Andrea Miniatures 54mm Cavalry Trooper; Right – Gringo 40s One Eyed Trail Boss

Custer’s Last Stand – 54mm Andrea Miniatures

 

Andrea Miniatures 54mm Mountain Man

Wargames Foundry 28mm Old West Men in the Wilderness (and below left)

 

Right – Dixon Miniatures 28mm Old West Figures

Dixon Miniatures 28mm Old West figures and stage coach (above and below).  The building, which has been heavily modified, is by Sarissa Precision

 

Above and below – Dixon Miniatures 28mm Old West figures featuring their Chuck Wagon.  Three of the figures have had minor conversions.

Gunfight at the OK Coral featuring Dixon Miniatures 28mm Old West figures with two minor conversions and scratch built buildings.

Under Attack – Diorama featuring Dixon Miniatures Old West Indians and US Army 28mm figures.

Diorama featuring Artizan 28mm Rail Worker figures, Sarissa Precision Old West Locomotive and scratch built Freight Depot.

 

Left – a break from the Old West but same era different continent!  Beneito Minjiatures 54mm Rorke’s Drift.  Right – Dixon Miniatures Confederate Soldier, the first figure in a new diorama.